Greg Lukosek is turning a former delivery van into a campervan for his family, with a ceiling-mounted bunk bed at the center of the design. Using his Makera Z1 Pro, the UK-based software developer has machined custom metal parts for the bed and seating platform, while exploring an AI-assisted workflow that connects his software skills with hands-on making.
“Having capabilities of cutting metal and making actual metal parts that are more durable and more precise than 3D printer will give me, that's really something I enjoy doing.”
— Greg Lukosek, creator of Puffin Campers
A Birthday Trip That Became a Family Project
The idea started in Iceland. For Greg’s 40th birthday in April 2026, his wife took him on a campervan trip around the island. They spent about 15 days traveling in a rented van, and Greg returned to the UK ready to build one of his own.
He began looking for a vehicle almost immediately. By May, he was starting work on a high-mileage former delivery van, with plans to turn it into a place his family could sleep, cook, work, and travel together.
The name, Puffin Campers, came from another family connection to Iceland: watching puffins arrive on the island to breed. That memory helped shape the Nordic theme he wanted for the conversion.
Greg’s ambitions extend beyond the interior layout. He is writing his own touchscreen control software and planning dynamic lighting and sensors throughout the van. Running a software development studio by day, he has found an after-work project that brings together many of the things he enjoys.
Four Beds and Room to Move
Greg set himself a demanding layout requirement: space for four adults to sleep, while keeping access to the shower, kitchen, and front seats when all the beds are open.
There was a personal reason for keeping that route clear. He likes to get up early and work on his laptop while the rest of his family sleeps. He wanted to reach a seat and desk without asking anyone to fold away a bed.
That requirement led to the conversion’s first major engineering project: a bunk bed that lowers from the ceiling and lifts out of the way when it is no longer needed.
Greg built the structure from aluminum profiles. At the time of the interview, the main bed assembly was complete, with further details, including additional restraint straps, still to be added. The full four-person layout also remained to be tested in use.
His favorite part is how little space the bed appears to occupy when raised:
“When you put it up, the bed disappears. It's so tightly up next to the ceiling you kind of don't see it at all.”
Returning to Machining with His First CNC
Although the campervan gave Greg plenty of reasons to machine metal, he had ordered his CNC before the trip that inspired the build.
He had studied mechanical engineering and used manual mills and lathes at school, but his career took him into software. He had wanted to return to machining for years. When he saw the Z1 Kickstarter campaign, he backed it and chose the Pro version.
The Makera Z1 Pro became his first CNC machine, joining a workshop where 3D printing was already well established. Greg bought his first printer around 2013 and had spent years using Fusion to design solutions to problems he encountered himself.
Metal machining added another option. He could continue using quick, inexpensive printed prototypes to check a shape or fit, then make selected components in metal when that better suited his design. The campervan soon supplied several opportunities to put that process to work.
Three Custom Parts for a Very Specific Layout
The most useful parts in Greg’s build solve small problems created by the wider layout. A few millimeters of clearance or a missing support column can determine whether the interior works as intended.
A Platform Profile That Preserves Drawer Space
One machining setup featured a long aluminum profile extending out of the Z1 Pro. It belonged to a raised platform beside the middle seats.
The seating height helped the bed layout work with the swiveling front seats, but it left the children’s feet too far from the floor. Greg needed a higher platform beneath their feet, with a steel bar running across it for reinforcement.
He locally milled the aluminum profile down by 8 mm to accommodate that bar. Using another profile would have taken space from the drawer underneath, so modifying the existing piece let him retain the storage clearance.
He clamped the profile in a low-profile vise and used AI to help generate the toolpath. He recalls completing the cut in about 15 minutes.
“I could probably do it by hand but it would not be as precise. It would be less fun.”
A Double-Sided Aluminum Bed Latch
The lowered bed presented a different problem: its lifting struts still pushed upward. Greg needed a latch to hold it in the down position.
He made an aluminum tongue that engages with a buckle, using a mechanism he compares to a seat belt. Machining the part required operations on both sides, so the challenge was locating it accurately after the flip.
Greg held the stock flat in his low-profile vise and used a 3D probe to locate it again for the second setup. He also used a 6 mm cutter and collet for the outline and material removal.
The result worked on the first attempt. Describing the transition between the two machined sides, he said:
“You could not really see the seam between those.”
At the interview, he had fitted two of the parts in the van and reported that they were doing their job.
A Fourth-Axis Connector That Keeps the Passage Clear
Another component helped Greg avoid putting a support column between the seats, where it would obstruct access to the cab.
His design instead uses a strap descending from the ceiling to support one corner of the bed. A small metal connector, approximately 35 × 35 mm, provides the connection between the ceiling and that strap.
Greg used the fourth axis to machine the component from several directions. He had considered a printed version, but for this particular application, with his daughter sleeping in the bed, he wanted to make the part in metal.
It was a compact part with a clear purpose: support the chosen layout while leaving the passage open.
Exploring a Path from AI to CNC
For Greg, learning CNC has also become a software project. He describes his experiment as “text to a CNC”: starting with requirements and working toward the G-code needed to make a physical part.
He built a workflow around Anthropic’s models, connecting Claude Code to Fusion through MCP and supplying information about his machine, setup, and available tools. For the fourth-axis bed connector, Greg designed the model himself and explored how AI could help prepare the machining operations.
He recalls spending roughly two hours iterating before obtaining the indexed fourth-axis toolpaths, followed by around three hours of machining. The limited selection of cutters he had available made planning the setups a substantial part of the task.
He also asked for documentation to accompany the machining files. The resulting material ran to about 15 pages, covering technical drawings, clamping positions, tool choices for individual operations, and pre-run checks.
This remains Greg’s own experimental workflow. He says the AI can make mistakes; his process includes simulation in Fusion 360 and previewing in Makera Studio. His interest is in bringing toolpaths, previews, and matching setup instructions together so a beginner can better understand each operation.
Despite the parts he has already made, Greg still considers himself a CNC beginner. The appeal is having a real project that gives him a reason to keep learning.
Enjoying the Build Before the First Journey
The campervan has become a much larger undertaking than Greg first expected. Small details can take weeks of design and testing, and some never make it into the final build.
He is aiming for summer 2027, while acknowledging that completion could move into 2028. His priority is a reliable vehicle he can feel comfortable taking farther from home.
An initial trip might be to Scotland to discover what works for the family. Later, he hopes to travel to Norway and toward the Arctic Circle. As a paramotor pilot, he also imagines carrying his equipment, sleeping in the van, and heading out for a morning flight.
For now, making the vehicle is already rewarding.
“I think I will enjoy building it more than actually using it.”
With the Z1 Pro in his workshop, Greg can take a custom component from a design into metal and fit it into the van he is building. Each part moves Puffin Campers a little closer to its first journey, while giving him another engineering problem to enjoy along the way.
Explore more
From CAD to Rocket Hardware: Akkoyun Aerospace’s Carvera Story